HPE Proliant DL580 G7

HPE ProLiant DL580 G7 Server - Specifications :-

Physical specifications

Specification Description

Dimensions (H x W x D) (With bezel) 17.6 x 48.3 x 70.0 cm (6.94 x 19.0 x 27.55 in)

Weight (Approximate)

Maximum (All hard drives, power supplies, DIMMs and processors installed) 45.4 kg (100.0 lb)

Minimum (One hard drive, two power supplies, four DIMMs, and two processors installed) 30.0 kg (66.0 lb)

Input requirements (Per power supply)

Rated line voltage 100 - 127 V ac, 200 - 240 V ac

Rated input current 12 A (At 100 V ac), 8 A (At 200 V ac)

Rated input frequency 50 to 60 Hz

Rated input power 1161 W (At 100 V ac), 1598 W (At 240 V ac)

BTU rating "Maximum
3960 BTU/hr (At 100 V ac), 5450 BTU/hr (At 200 V ac)"

Power supply output (Per power supply) "Rated Steady-State power
910 W (Low line), 1300 W (High line)
Maximum peak power
910 W (Low line), 1300 W (High line)"

Environmental specifications

Specification Description

Temperature range

Operating temperature "10° to 35°C (50° to 95°F) at sea level with an altitude derating of 1.0°C per every 305 m (1.8°F per every 1000 ft) above sea level to a maximum of 3050 m (10,000 ft), no direct sustained sunlight. Maximum rate of change is 10°C/hr (18°F/hr). The upper limit may be limited by the type and number of options installed.
System performance may be reduced if operating with a fan fault or above 30°C (86°F)."

Non-operating temperature -30° to 60°C (-22° to 140°F). Maximum rate of change is 20°C/hr (36°F/hr).

Relative humidity (Non-Condensing)

Operating 10% to 90% relative humidity (Rh), 28°C (82.4°F) maximum wet bulb temperature, noncondensing.

Non-operating 5% to 95% relative humidity (Rh), 38.7°C (101.7°F) maximum wet bulb temperature, noncondensing.

Altitude

Operating 3050 m (10,000 ft). This value may be limited by the type and number of options installed. Maximum allowable altitude change rate is 457 m/min (1500 ft/min).

Non-operating 9144 m (30,000 ft). Maximum allowable altitude change rate is 457 m/min (1500 ft/min).

Acoustic noise "Listed are the declared A-Weighted sound power levels (LWAd) and declared average bystander position A-Weighted sound pressure levels (LpAm) when the product is operating in a 23°C ambient environment. Noise emissions were measured in accordance with ISO 7779 (ECMA 74) and declared in accordance with ISO 9296 (ECMA 109)
Idle
L WAd
6.4 B (Wth PCI-E)
L pAm
NA dBA
Operating
L WAd
6.8 B (Wth PCI-E)
L pAm
NA dBA"

Safety certifications

Certifications Description

FCC rating Class A

Normative standards CISPR 22; EN55022; EN55024; FCC CFR 47, Pt 15; ICES-003; CNS13438; GB9254; K22;K24; EN 61000-3-2; EN 61000-3-3; EN 60950-1; IEC 60950-1

Integrated Lights-Out 3 (iLO 3) integrated on system board

Specification Description

Architecture PCI Express based health and remote management ASIC

Processor PCI Express RISC processor core running at 250 MHz

Upgradeability Option firmware upgradeable via Flash ROM

Interfaces "One Ethernet Sideband connection (10/100/1000 Mb/s)

One Ethernet network connection (10/100 Mb/s)"

Memory 128MB RAM with ECC

Command line support "Secure shell and serial port access

Secure socket layer

Secure shell version 2"

Security "Advanced Encryption Standard (AES) and Triple Data Encryption Standard (3DES) on browser, CLP and XML scripting interface

AES encryption of video

RC4 encryption of video"

Directory support services Active directory v1.0 (Windows 2003)

Driver support HP ProLiant iLO3 management controller driver package

Management protocols supported SNMP, IPMI 2.0 (System and LAN interface), DMTF Systems Management Architecture for Server Hardware Command Line Protocol (SMASH CLP), HP RIBCL XML

Smart Array P410i controller

Specification Description

Dimensions Embedded

Disk drive and enclosure interface - Transfer rate "6 Gb/s Serial Attached SCSI (SAS)

3 Gb/s SATA (Serial ATA)"

SAS connectors 2 internal 4X connectors

Cache memory speed DDR2-800 MHz with 40 or 72-bit wide bus

Server interface x4 PCIe 2.0 provides 2 GB/s maximum bandwidth

SAS speed 8 6 GB/s SAS links provide 4.8 GB/s maximum bandwidth

Cache memory "Zero memory RAID has no cache memory

40-bit 256MB ECC protected cache (Battery upgrade available)

72-bit 512MB BBWC or 72-bit 512MB and 1G FBWC"

Logical drives Zero memory, Up to 2 logical volumes (8 Physical drives)

Supported Up to 64 logical drives with cache

Host memory addressing 64-bit, supporting greater than 4GB server memory space

RAID support "RAID 6, 6+0 (Advanced data guarding)

RAID 5, 5+0 (Distributed data guarding)

RAID 1+0 (Striping and mirroring)

RAID 0 (Striping), RAID 1 (Mirroring)"

top

HPE NC375i Integrated quad port gigabit server adapter

Specification Description

Network interface 10Base-T/100Base-TX/1000Base-TX

Compatibility "IEEE 802.3 10Base-T

IEEE 802.3ab 1000Base-T

IEEE 802.3u 100Base-TX

IEEE 802.3ad 1000Base-TX

IEEE 802.1p 100Base-TX

IEEE 802.1q 100Base-TX"

Data transfer method PCI-Express 2.0 x8

Controller Qlogic/NetXen NX3031

Network transfer rate 10Base-T (Full-Duplex) 20 Mb/s

100Base-TX (Full-Duplex) 200 Mb/s

1000Base-TX (Full- Duplex) 2000 Mb/s

Connector RJ-45

Cable support 10Base-T Categories 3, 4, or 5 UTP; up to 328 ft (100 m)

100Base-TX Category 5 or higher UTP; up to 328 ft (100 m)

1000Base-TX Category 5 or higher UTP; up to 328 ft (100 m)

top

Electrical specifications

Specification Description

Input requirements

Rated input voltage 100 to 120 V ac, 200 to 240 V ac

Rated input frequency 50 Hz to 60 Hz

Rated input current "10 A at 100 V ac
4.9 A at 200 V ac"

Rated input power "930 W at 100 V ac input
1348 W at 200 V ac input"

BTUs per hour "3530 at 120 V ac input
4600 at 200 V to 240 V ac input"

Power supply output

Rated Steady-State power "800 W at 100 V ac input
900 W at 120 V ac input
1200 W at 200 V to 240 V ac input"

Maximum peak power "800 W at 100 V ac input
900 W at 120 V ac input
1200 W at 200 V to 240 V ac input"

‍